자유게시판 글답변

본문 바로가기

사이트 내 전체검색

자유게시판 글답변

이름필수
비밀번호필수
이메일
홈페이지
분류필수
제목필수
내용필수	웹에디터 시작 > > > </p><br/><p>Using basic equipment to verify roller pressure is a smart, cost-effective method for <a href="http://121.181.234.77/bbs/board.php?bo_table=blessed_pray&wr_id=601143">غلطک پرس پرینتر</a> maintaining optimal machine performance<br/></p><br/><p>This test is commonly used in printing, laminating, and paper processing industries where consistent roller pressure is critical for quality output<br/></p><br/><p>Professional calibration tools aren’t required to detect pressure inconsistencies<br/></p><br/><p>Many operators use everyday supplies to monitor roller performance without investing in specialized instruments<br/></p><br/><p>Begin by collecting the necessary equipment<br/></p><br/><p>A thin sheet of paper, such as 20 lb. printer paper, is ideal for capturing pressure impressions<br/></p><br/><p>Make sure you have a tape measure, a pen or pencil, and a smooth, level workspace<br/></p><br/><p>Make sure the roller system is turned off and cooled down before beginning<br/></p><br/><p>Position both rollers so they make full, unimpeded contact along their entire length<br/></p><br/><p>Insert the paper directly in the middle of the roller gap, where the main compression occurs<br/></p><br/><p>Run the rollers at their typical speed and pressure setting during normal use<br/></p><br/><p>Be sure to follow your machine’s standard operating procedure for engagement<br/></p><br/><p>Once the rollers have passed over the paper, stop the machine and carefully remove the paper<br/></p><br/><p>Look for the impression left by the rollers<br/></p><br/><p>The pressure mark should be even and continuous from edge to edge<br/></p><br/><p>If the mark is uneven—darker or deeper in some areas and lighter in others—it indicates uneven pressure distribution<br/></p><br/><p>Measure the length of the flattened section with a precision ruler or tape<br/></p><br/><p>Subtract the compressed width from the original paper width to calculate total compression<br/></p><br/><p>The difference will tell you how much the paper was compressed<br/></p><br/><p>Test at multiple locations to verify uniformity across the entire roller surface<br/></p><br/><p>Record each measurement<br/></p><br/><p>If the compression differs by more than 10 percent between any of the three points, your rollers may need alignment or maintenance<br/></p><br/><p>Uneven pressure can cause print defects, material damage, or premature wear<br/></p><br/><p>Contamination or degraded hardware can distort pressure distribution<br/></p><br/><p>Clean the roller surfaces and check for visible signs of damage<br/></p><br/><p>To ensure your results are repeatable, always use the same type and thickness of paper for each test<br/></p><br/><p>Changes in humidity or ambient temperature may alter paper compression characteristics<br/></p><br/><p>This simple method gives you a clear visual and measurable indication of roller pressure uniformity<br/></p><br/><p>Regular use of this method helps avoid unexpected failures and enhances output reliability<br/></p><br/><p>Frequent inspections reduce wear and ensure every print run meets quality standards<br/></p><img><br/><p>If you notice persistent issues after multiple tests, consult your equipment manual or a trained technician<br/></p><br/><p>Simple tools can tell you a lot, but > > 웹 에디터 끝
자동등록방지	자동등록방지 자동등록방지 숫자를 순서대로 입력하세요.

취소

회사소개 개인정보취급방침 서비스이용약관 모바일 버전으로 보기 상단으로

대전광역시 유성구 계룡로 105 (구. 봉명동 551-10번지) 3, 4층 | 대표자 : 김형근, 김기형 | 사업자 등록증 : 314-25-71130
대표전화 : 1588.7655 | 팩스번호 : 042.826.0758
Copyright © CAMESEEING.COM All rights reserved.

접속자집계

오늘: 8,699
어제: 12,838
최대: 16,322
전체: 6,189,664

-->
Warning: Unknown: write failed: Disk quota exceeded (122) in Unknown on line 0

Warning: Unknown: Failed to write session data (files). Please verify that the current setting of session.save_path is correct (/home2/hosting_users/cseeing/www/data/session) in Unknown on line 0